1：地板透明化（注：透明物體最后畫出）
    g_pd3dDevice->SetRenderState(D3DRS_ALPHABLENDENABLE,TRUE );
    g_pd3dDevice->SetRenderState(D3DRS_SRCBLEND,D3DBLEND_SRCALPHA );
    g_pd3dDevice->SetRenderState(D3DRS_DESTBLEND,D3DBLEND_INVSRCALPHA);

2：畫出反射對象（注：一份頂點數據通過矩陣變換畫出反射對象）
 D3DXMATRIXA16 tmp;
 D3DXMatrixScaling(&tmp,1,-1,1);//通過放縮矩陣來實現倒影(或D3DXMatrixReflect(&tmp,&plane);)

3：Stencil Buffer 模板緩存（啟用Stencil Buffer保證轉到地板下面時看不到實際存在的反射物體以免漏餡）
鏡面既要最先畫又要最后畫，那么畫兩遍，最先畫時設置Aphha混合如下不改變后臺緩存只是在模板緩存中標記鏡面區域?yàn)?.
最先畫地板時：
 //設置模板緩存
 g_pd3dDevice->SetRenderState(D3DRS_STENCILENABLE,true);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILFUNC,D3DCMP_ALWAYS);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILREF,0x1);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILMASK,0xffffffff);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILWRITEMASK,0xffffffff);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILZFAIL,D3DSTENCILOP_KEEP);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILFAIL,D3DSTENCILOP_KEEP);
 g_pd3dDevice->SetRenderState(D3DRS_STENCILPASS,D3DSTENCILOP_REPLACE);
 

 //繪制地板鏡面
 g_pd3dDevice->SetRenderState(D3DRS_ZENABLE, FALSE);
 g_pd3dDevice->SetRenderState(D3DRS_ALPHABLENDENABLE,TRUE);
 g_pd3dDevice->SetRenderState(D3DRS_SRCBLEND,D3DBLEND_ZERO);
 g_pd3dDevice->SetRenderState(D3DRS_DESTBLEND,D3DBLEND_ONE);
繪制物體影像時啟用模板緩存并對其函數狀態進行設置：
     g_pd3dDevice->SetRenderState(D3DRS_STENCILENABLE,true);
     g_pd3dDevice->SetRenderState( D3DRS_STENCILFUNC,D3DCMP_EQUAL);
最后在渲染時照常：
    g_pd3dDevice->SetStreamSource( 0, obj.g_pVB, 0, sizeof(CUSTOMVERTEX) );
    g_pd3dDevice->SetFVF( D3DFVF_CUSTOMVERTEX );
    g_pd3dDevice->SetIndices( obj.g_pIB );
    g_pd3dDevice->SetTexture( 0, g_pTexture[obj.textureID] ); //設置紋理
    g_pd3dDevice->DrawIndexedPrimitive(D3DPT_TRIANGLELIST,0,0,obj.numOfVertex,0,obj.numOfFace);
其中 g_pd3dDevice->DrawIndexedPrimitive(D3DPT_TRIANGLELIST,0,0,obj.numOfVertex,0,obj.numOfFace);這句話根據模板緩存的設置及開啟情況，寫入后臺緩沖區的同時寫入模板緩存?；蛟谂c模板緩存中數據比較后決定是否要往后臺緩沖區中寫。